miércoles, 23 de abril de 2008

FOTO DEL REMACHADO


Es la foto cuando estaba remachando el lapicero con la remachadora.

It was photo riveting when the penciholder with the rivets.

FOTO DEL LIJADO


Esta es la foto cuando estaba lijando el metal.

This is when the photo was lijando metal.

FOTO DEL GRANATEADO

Esta es la foto de cuando estaba granateando el metal , es decir haciendole los agujeros.

This is the photo of when I was maroon metal, ie make the holes.

miércoles, 9 de abril de 2008

FOTO DEL RECORTE DEL DESPIECE


Esta es la foto cuando estaba recortando el despiece con unas tijeras de recortar metal.

This is the photo when he was cutting cutting with scissors to cut metal.

FOTO DEL DESPIECE


Esta es la foto del dibujo del despiece del lapicero a lápiz en el metal.

This is the photo of the drawing of cutting the pen to penciholder in the metal.

miércoles, 2 de abril de 2008

ALUMINIO


El aluminio es un elemento químico, de simbolo Al y numero atómico 13. Se trata de un metal no ferroso. Es el tercer elemento más común encontrado en la corteza terestre. Los compuestos de aluminio forman el 8% de la corteza de la tierra y se encuentran presentes en la mayoria de las rocas, de la vegetacion y de los animales.

Aluminum is a chemical element, atomic number and symbol at 13. This is a non-ferrous metal. It is the third most common element found in the bark terestre. The aluminum compounds form 8% of the earth's crust and are present in most rocks, the vegetation and animals.

HERRAMIENTAS




GRANETE:Se denomina granetea una herramienta manual que tiene forma de puntero de acero templado afilado en un extremo con una punta de 60º aproximadamente que se utiliza para marcar el lugar exacto que se ha trazado previamente en una pieza donde haya que hacerse un agujero,cuando no se dispone de una plantilla adecuada.

Granet: It's called a tool granetea manual that is shaped like a sharp tempered steel pointer on one end with a tip of approximately 60 th which is used to mark the exact place that has been charted previously in a room where a hole has to be done, when there is no appropriate staffing capacity.




SARGENTO:Se denomina sargento a una herramienta manual de uso comun en muchas profesiones,principalmente en carpintería, que se compone de dos morzadas,regulables con un tornillode presion.

Sargent: It's called sergeant to a hand tool commonly used in many professions, mainly in carpentry, which consists of two morza, with an adjustable tornillode pressure.




REMACHADORA:Se denomina remachadora a una herramienta manual usada princuipalmente en talleres de bricolaje y carpinteria metalica que sirve para fijar con remaches uniones de piezas que no son desmontables.

Rivets: It's called a riveting princuipalmente hand tool used in carpentry workshops and DIY metal used to set rivets with unions pieces that are not removable.






PUNTA DE TRAZAR:Se denomina punta de trazar a una herramienta manual de acero templado que tiene la forma de una varillaredonda delgada y una punta muy afilada.

DE TRAZAR point: It's called rush to chart a hand tool of hardened steel that is shaped like a thin varillaredonda and a very sharp tip.

martes, 1 de abril de 2008

CALCULO DE ÁREAS

Figura A=b.a=4.5=20=b.a=5.5=25/2=12´5=20+12´5=32´5.2=65 cm2

Figura B=b.a=4.7=28 cm2

Figura c=b.a=7.9=63 cm2

Figura D=b.a=7.10=70 cm2

A+B+C+D=65+28+63+70=226 cm2

PERSPECTIVA CABALLERA



La perspectiva caballera es una perspectiva de la figura a regla se con tres líneas alto de alzado, ancho de alzado y ancho de perfil se hace a lápiz luego se rotula con rotulador fino negro y por último se pinta.

The prospect is a prospect of Knights figure to rule with three lines of high standard, standard width and breadth of profile is done in pencil then rotula with fine black marker and finally painted.

PERSPECTIVA ISOMETRICA


La perspectiva isométrica es hacer un dibujo de la figura con una posición determinada que alto dealzado , ancho de alzado y ancho de perfil se hace arregla luego se repasa con rotulador fino negro y por último se pinta.

The isometric perspective is to make a drawing of the figure with a certain position that high dealzado, width and breadth of standard profile is then arranges reviews with fine black marker and finally painted.

DESPIECE


El despiece es una construcción de de cada una de las piezas que forman la figura a lápiz acotada e indicando donde estan situados los agujeros de los ingletes, se pasa a rotulador fino negro y después se pinta.

Cutting is a construction of each of the pieces that make up the figure mentioned in pencil and indicating where the holes are located in the tabs, it's going to fine black marker and then paint.